🌱Megaponics← All guides
🌿
Hydroponic grow guide · Herbs, Micro & Leafy Greens

Basil

🔥 Warm-season crop — likes it warm🪣 NFT · DWC / raft

Basil is a warm-season herb that hates the cold. Kept at 72–77°F and pinched often, one plant gives you a harvest every week for months. Let it flower and leaf growth slows and the flavor drops, so the job is mostly pinching.

TDS
850–950 ppm
EC
1.7–1.9
pH
5.8–6.2
Stages
7
Day temp
72–77°F

Stage by stage

1
Sowing & germination
Sprouts in 5–7 days

Basil seed is tiny and sprouts fast in warmth. Cold is the one thing that stops it.

  1. Day 0Soak plugs in plain water set to pH 5.8, then squeeze out the extra.
  2. Day 0Drop 2–3 seeds on each plug and barely cover them.
  3. Keep the plugs at 72–77°F under a humidity dome.
  4. Once upKeep the strongest one or two seedlings per plug and snip the rest at the base.

Watch for Below 50°F (10°C) basil seedlings blacken and stall. Keep trays off cold windowsills and floors.

Looks right Two round, bright-green seed leaves within 5–7 days.

🌡️ Target climate — this stage
Air · day
72–77°F22–25°C
Air · night
64–68°F18–20°C
Root zone
68–75°F20–24°C
Humidity
60–75%
VPD
0.5–0.8 kPa
DLI
8–12 mol
Light hours
14–16 h
Duration
5–7 days

💡 Basil is cold-sensitive — keep everything ≥18°C; chilling causes blackening.

🧪 Feed

Plain water only — no nutrients until it sprouts.

Seedling: in the tray or plug

Young roots burn easily, so the feed starts weak and steps up in 3 small steps (EC 0.3 → 0.5 → 0.7). Move on when the plant looks like the next step, not by the calendar.

2
Step 1 of 3 · Seed leaves open
Seed leaves open flat. The seed itself gets plain water only.

The seed leaves are feeding the plant for now. A weak feed (EC 0.3) gives it a gentle start.

  1. Mix the first feed at 150 ppm and set pH to 5.8.
  2. Water from below and let the extra drain so plugs stay moist, not soggy.
  3. Run the light 14–16 hours a day, close enough that stems stay short.

Watch for Seedlings that pinch in and fall over at the base have damping off. Water less and add airflow.

Looks right Short, sturdy stems with round seed leaves.

🧪 Feed — weigh into a fresh tank
Target TDS 150 ppm · EC 0.3 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

3
Step 2 of 3 · First true leaves
First jagged true leaves are showing.

True leaves are the first real basil leaves, and they start feeding the plant.

  1. Raise the feed to 250 ppm, pH 5.8.
  2. Keep the air at 72–77°F. Basil grows slowly when it's cool.
  3. Start a small fan on low.

Watch for Yellow between the veins of new leaves often means pH drifted high and iron got locked out. Check pH before adding anything.

Looks right Glossy, slightly cupped true leaves that smell like basil when you touch them.

🧪 Feed — weigh into a fresh tank
Target TDS 250 ppm · EC 0.5 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

4
Step 3 of 3 · Ready to transplant
Roots fill the plug — ready to move into the system.

Roots are filling the plug. Moving now keeps them from tangling and stalling the plant.

  1. Feed at 350–400 ppm, pH 5.8.
  2. Move it once white roots show through the bottom of the plug.
  3. Give it a few days of extra airflow first so the stems toughen up.

Watch for Seedlings left too long in their plugs get root-bound and stall for days after the move. Transplant on time.

Looks right Two or three pairs of true leaves and white roots out of the bottom of the plug.

🧪 Feed — weigh into a fresh tank
Target TDS 350–400 ppm · EC 0.7–0.8 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

After transplant: first days in your system

Moving a seedling tears its fine roots, so strength drops back down and climbs again over 3 steps (EC 0.3 → 0.5 → 0.7).

5
Step 1 of 3 · Just transplanted
Just moved. Strength drops back so roots settle.

The move shocks the roots, so the feed drops back while they settle in.

  1. Set the plug in its net cup so the bottom just touches the water. Keep the stem dry.
  2. Drop the feed to 150 ppm, pH 5.8.
  3. Keep the room at 72–77°F by day and 64–68°F at night. Basil sulks in a cold room.

Watch for Drooping that lasts past day three means the roots can't reach the water. Raise the level or lower the cup.

Looks right Leaves stand back up within a day or two.

🧪 Feed — weigh into a fresh tank
Target TDS 150 ppm · EC 0.3 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

6
Step 2 of 3 · Roots into system
New white roots are growing into the system.

Roots are growing into the water, and this is where basil starts to take off.

  1. Feed at 250 ppm, pH 5.8.
  2. Keep the root zone at 68–75°F.
  3. As roots lengthen, drop the water level a little to leave them an air gap.

Watch for Brown, slimy roots mean root rot. Check that the water isn't too warm and the air pump is running.

Looks right White roots trailing into the reservoir and fresh leaves at the top.

🧪 Feed — weigh into a fresh tank
Target TDS 250 ppm · EC 0.5 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

7
Step 3 of 3 · Before crop feed
Settled in. Flush with plain water, then start Vegetative.

Roots are settled. A fresh tank now gets the plant ready for the full recipe.

  1. Feed at 350–400 ppm, pH 5.8.
  2. Before Vegetative, dump the tank, rinse with plain water, then mix the new recipe fresh.

Watch for Mixing the stronger recipe on top of old feed stacks up salts and burns the leaf edges. Always start the new stage from a fresh tank.

Looks right An upright plant with three or four pairs of leaves.

🧪 Feed — weigh into a fresh tank
Target TDS 350–400 ppm · EC 0.7–0.8 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

Growing: full feed

Roots are settled. The plant now gets its full recipe for each stage.

8
Vegetative
From transplant to harvest — keep pinching flower buds.

From here to the end it's one recipe. Every pinch turns one stem into two, so the more you harvest, the bushier it gets.

  1. Feed at 850–950 ppm (EC 1.7–1.9), pH 5.8–6.2.
  2. When the plant is about 6 in. tall, pinch the top off just above a pair of leaves.
  3. Harvest from the top every week, always cutting just above a leaf pair.
  4. Pinch off flower buds as soon as they show.
  5. Top up with plain water as the level drops and change the whole tank every 1–2 weeks.

Watch for Yellow patches on top of the leaves with gray-purple fuzz underneath mean downy mildew. Bring humidity down to 55–70% and add airflow; it spreads fast.

Looks right A bushy plant with lots of stems and big glossy leaves, and no flower spikes.

🌡️ Target climate — this stage
Air · day
72–77°F22–25°C
Air · night
64–68°F18–20°C
Root zone
68–75°F20–24°C
Humidity
55–70%
VPD
0.8–1.1 kPa
DLI
16–29 mol
Light hours
14–16 h
Duration
21–35 days

💡 Harvest by pinching above a leaf node to drive bushy regrowth; remove flower spikes to keep leaf quality.

🧪 Feed — weigh into a fresh tank
Target TDS 850–950 ppm · EC 1.7–1.9 · pH 5.8–6.2

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8–6.2.

Fix a deficiency

Iron
Interveinal chlorosis of new growth; common above pH 6.5.
Fix: Fe-EDTA (and check pH ≤6.5)
Nitrogen
Overall pale, small leaves; older foliage yellows first.
Fix: Calcium Nitrate / Potassium Nitrate
Magnesium
Interveinal yellowing of older leaves (MgSO₄ already heavy in this recipe — check pH/antagonism first).
Fix: Magnesium Sulfate
Micronutrients (B/Mn/Zn/Cu/Mo)
Trace-element symptoms (distorted/spotty new growth).
Fix: Increase Micro Nutrient Mix