🌱Megaponics← All guides
🍅
Hydroponic grow guide · Vegetables

Cherry Tomato

🌤️ Mild-temperature crop🪣 Dutch bucket (bato) · Drip / rockwool slab

Cherry tomatoes are the easiest fruiting crop to start in hydroponics. Small fruit ripen faster than slicers, and one indeterminate vine keeps cropping for months. They want steady warmth, 70–75°F days with no big swings at night, and indoors you do the pollinating yourself.

TDS
600–1250 ppm
EC
1.2–2.5
pH
6–6.5
Stages
10
Day temp
68–79°F

Stage by stage

1
Sowing & germination
Sprouts in 5–10 days

Tomato seed needs warmth far more than light to sprout. A warm, evenly moist plug is the whole job.

  1. Day 0Soak rockwool plugs in plain water set to pH 5.8, then squeeze out the extra.
  2. Day 0Sow one seed per plug, about ¼ in. deep. Sow a few extra plugs as backups.
  3. Keep the plugs at 75–79°F under a humidity dome. A seedling heat mat helps most in a cool room.
  4. Once upTake the dome off and put them under light the same day, or the stems stretch thin.

Watch for Nothing up after 5–10 days? The plugs are usually too cold or too wet. Re-sow with fresh seed instead of waiting longer.

Looks right A hooked stem pushes up, then straightens and opens two smooth seed leaves.

🌡️ Target climate — this stage
Air · day
75–79°F24–26°C
Air · night
75–79°F24–26°C
Root zone
75–79°F24–26°C
Humidity
70–85%
VPD
0.4–0.8 kPa
DLI
4–8 mol
Light hours
14–16 h
Duration
5–10 days

💡 Germinate warm (24–26°C); cherry types are vigorous and emerge fast.

🧪 Feed

Plain water only — no nutrients until it sprouts.

Seedling: in the tray or plug

Young roots burn easily, so the feed starts weak and steps up in 3 small steps (EC 0.3 → 0.5 → 0.7). Move on when the plant looks like the next step, not by the calendar.

2
Step 1 of 3 · Seed leaves open
Seed leaves open flat. The seed itself gets plain water only.

The seed's stored food is nearly used up. A very weak feed (EC 0.3) starts the seedling without burning its tiny roots.

  1. Mix the first feed at 150 ppm and set pH to 5.8.
  2. Water from below and let the extra drain away so plugs stay moist, not soggy.
  3. Run the light 14–16 hours a day, close enough that stems stay short.

Watch for Tall, pale, floppy stems mean too little light. Move the light closer; a stronger feed won't fix it.

Looks right Short, thick stems and two flat, deep-green seed leaves.

🧪 Feed — weigh into a fresh tank
Target TDS 150 ppm · EC 0.3 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

3
Step 2 of 3 · First true leaves
First jagged true leaves are showing.

True leaves do the real photosynthesis, so the plant can now use a little more food.

  1. Step the feed up to 250 ppm (EC 0.5), pH 5.8.
  2. Keep the air at 68–72°F by day and 64–68°F at night.
  3. Run a small fan on low. Gentle movement builds thicker stems.

Watch for Purple undersides on the leaves usually mean cold roots, not a missing nutrient. Warm the room before you add anything.

Looks right The first jagged true leaves, with that sharp tomato smell when you brush them.

🧪 Feed — weigh into a fresh tank
Target TDS 250 ppm · EC 0.5 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

4
Step 3 of 3 · Ready to transplant
Roots fill the plug — ready to move into the system.

Roots are filling the plug. Moving now, before they circle, avoids a long stall after transplant.

  1. Feed at 350–400 ppm, pH 5.8.
  2. Check the bottom of the plug. White root tips poking out means it's time to move.
  3. Harden it off for about a week first: a slightly cooler room and more air movement.

Watch for Brown, slimy roots in the plug mean it stayed too wet. Let plugs dry a little between waterings.

Looks right Several true leaves and clean white roots showing out of the bottom of the plug.

🧪 Feed — weigh into a fresh tank
Target TDS 350–400 ppm · EC 0.7–0.8 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

After transplant: first days in your system

Moving a seedling tears its fine roots, so strength drops back down and climbs again over 3 steps (EC 0.3 → 0.5 → 0.7).

5
Step 1 of 3 · Just transplanted
Just moved. Strength drops back so roots settle.

Moving disturbs the roots. A weak feed lets them settle in instead of fighting salty water.

  1. Set the plug so its bottom just touches the water or sits on the drip line. Keep the stem dry.
  2. Drop the feed back to 150 ppm, pH 5.8.
  3. Raise the light a little for a day or two if the leaves droop.

Watch for Some droop on the first day is normal. Droop after three days usually means roots can't reach the water, so raise the level or lower the cup.

Looks right Leaves perk back up within a day or two.

🧪 Feed — weigh into a fresh tank
Target TDS 150 ppm · EC 0.3 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

6
Step 2 of 3 · Roots into system
New white roots are growing into the system.

New white roots are growing into the system. This is when the plant starts drinking for itself.

  1. Raise the feed to 250 ppm, pH 5.8.
  2. Keep the root zone at 68–72°F.
  3. In DWC, drop the water level a little as roots lengthen to leave them an air gap.

Watch for Brown, slimy, smelly roots are root rot. Check the water temperature first; warm water holds less oxygen.

Looks right Bright white root tips spreading out into the reservoir.

🧪 Feed — weigh into a fresh tank
Target TDS 250 ppm · EC 0.5 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

7
Step 3 of 3 · Before crop feed
Settled in. Flush with plain water, then start Vegetative.

Roots are established. A fresh tank now resets things before the stronger crop recipe starts.

  1. Feed at 350–400 ppm, pH 5.8.
  2. Before Vegetative, dump the tank, rinse with plain water, then mix the new recipe fresh.
  3. Put the trellis string or stake in now, while it's easy.

Watch for Never mix the stronger recipe on top of old feed. Salts stack up and burn the leaf edges.

Looks right A sturdy, upright plant putting out new leaves steadily.

🧪 Feed — weigh into a fresh tank
Target TDS 350–400 ppm · EC 0.7–0.8 · pH 5.8

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 5.8.

Growing: full feed

Roots are settled. The plant now gets its full recipe for each stage.

8
Vegetative
Until the plant is 14–16 in. tall.

The vine builds the stem and leaves that will carry every truss. Strong growth now means more fruit later.

  1. Feed at 600–700 ppm (EC 1.2–1.4), pH 6.0–6.5.
  2. Once a week, pinch out suckers, the shoots between a leaf and the main stem. One or two main stems is plenty.
  3. Wind the main stem around its string every few days.
  4. Top up with plain water as the level drops and change the whole tank every 1–2 weeks.

Watch for Bushy, dark plants with flowers slow to show usually need more light. Give them the full 14–16 hours a day before changing the feed.

Looks right A thick main stem with leaves close together, reaching 14–16 in. tall when the first flowers come.

🌡️ Target climate — this stage
Air · day
70–75°F21–24°C
Air · night
61–64°F16–18°C
Root zone
68–72°F20–22°C
Humidity
65–80%
VPD
0.8–1 kPa
DLI
14–20 mol
Light hours
14–16 h
Duration
21–35 days

💡 Cherry types are vigorous — train and prune suckers to keep airflow.

🧪 Feed — weigh into a fresh tank
Target TDS 600–700 ppm · EC 1.2–1.4 · pH 6.0–6.5

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 6.0–6.5.

9
Flowering
14–16 in. tall until the first truss's fruit is ¼–½ in. across.

Every flower that sets becomes a tomato. Indoors there's no wind or bees, so the pollinating is up to you.

  1. Feed at 850–950 ppm (EC 1.7–1.9), pH 6.0–6.5.
  2. Every day or two around midday, tap each flowering truss or buzz it with an electric toothbrush.
  3. Hold days at 70–75°F and nights at 61–64°F. Big swings make flowers drop.
  4. Keep pinching suckers so the energy goes to the trusses.

Watch for Flowers that dry up and fall without fruit usually mean poor pollination, or air that's too hot or too dry.

Looks right Clusters of yellow star-shaped flowers, with tiny green fruit forming as the petals fade.

🌡️ Target climate — this stage
Air · day
70–75°F21–24°C
Air · night
61–64°F16–18°C
Root zone
68–72°F20–22°C
Humidity
60–75%
VPD
0.8–1.1 kPa
DLI
18–24 mol
Light hours
14–16 h
Duration
14–28 days

💡 Cherry trusses set many small fruit — steady warmth keeps set even.

🧪 Feed — weigh into a fresh tank
Target TDS 850–950 ppm · EC 1.7–1.9 · pH 6.0–6.5

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 6.0–6.5.

10
Fruiting
After the first fruit sets.

Fruit are swelling and pulling hard on calcium and potassium. Steady water and feed now prevent split and rotten fruit.

  1. Feed at 1100–1250 ppm (EC 2.2–2.5), pH 6.0–6.5.
  2. Check EC and pH every day. Add plain water when EC climbs, and feed when it drops.
  3. Strip yellowing leaves below the lowest ripening truss to open up airflow.
  4. Keep humidity at 60–75% with a fan running.

Watch for Dark, sunken patches on the bottom of the fruit are blossom-end rot. It comes from uneven watering or humid, still air, not from too little calcium in the tank.

Looks right Clusters of firm green fruit sizing up, with the oldest truss starting to turn.

🌡️ Target climate — this stage
Air · day
70–75°F21–24°C
Air · night
64–65°F17.5–18.5°C
Root zone
68–72°F20–22°C
Humidity
60–75%
VPD
0.9–1.2 kPa
DLI
20–30 mol
Light hours
14–16 h
Duration
21–45 days

💡 Calcium-critical: keep watering steady to avoid splitting and blossom-end rot.

🧪 Feed — weigh into a fresh tank
Target TDS 1100–1250 ppm · EC 2.2–2.5 · pH 6.0–6.5

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 6.0–6.5.

11
Harvest
Picking — same recipe as Fruiting until the crop ends.

A cherry vine keeps flowering at the top while you pick at the bottom, so the same recipe runs for months.

  1. Keep feeding at 1100–1250 ppm, pH 6.0–6.5, the same as Fruiting.
  2. Pick fruit when fully colored but still firm, every day or two so ripe ones don't split.
  3. When the vine reaches the top of your space, lower it on its string and lean it sideways.

Watch for Fruit splitting right after a big top-up of plain water. Top up a little and often instead.

Looks right Glossy, evenly colored fruit that come off the vine with a gentle twist.

🌡️ Target climate — this stage
Air · day
70–75°F21–24°C
Air · night
64–65°F17.5–18.5°C
Root zone
68–72°F20–22°C
Humidity
60–75%
VPD
0.9–1.2 kPa
DLI
20–30 mol
Light hours
14–16 h
Duration
30–120 days

💡 Indeterminate — targets repeat per cluster through a long harvest window.

🧪 Feed — weigh into a fresh tank
Target TDS 1100–1250 ppm · EC 2.2–2.5 · pH 6.0–6.5

Mix in the calculator's order: Part A (Calcium Nitrate, Potassium Nitrate, Fe-EDTA), then Part B (MKP, Potassium Sulfate, Magnesium Sulfate), then the micro mix last. Dissolve each salt fully before the next, and never mix A and B together undiluted. Check TDS, then set pH to 6.0–6.5.

Fix a deficiency

Calcium
Blossom-end rot; fruit splitting under erratic watering.
Fix: Calcium Nitrate
Iron
Interveinal yellowing of young leaves (veins stay green).
Fix: Fe-EDTA (check pH ≤6.5)
Nitrogen
Chlorosis of older leaves; purpling of stems/petioles.
Fix: Calcium Nitrate / Potassium Nitrate
Micronutrients (B/Mn/Zn/Cu/Mo)
Trace symptoms — e.g. boron: blotchy ripening, deformed tips.
Fix: Increase Micro Nutrient Mix